Some time ago I took a class in cloisonné enameling and
returned quite eager to get started on my first project. So I took the plunge
and ordered some fine silver cloisonné wire and a whole spectrum of yummy
colors of transparent Japanese leaded enamels. I chose Japanese enamels for the
brilliance and variety of colors; I chose transparent enamels as opposed to
opaque enamels so that the fine silver backdrop of my piece with its wave
texture would be visible through the enamel. Opaque enamels might be better suited over copper, for
example, or where the background of your enameled piece doesn’t need to be
visible.
In order to determine exactly how these colors would fire over fine silver – it
should be noted that fired enamels bear very little, if any, resemblance to
their appearance in powder form -- I made a color test strip. Not wanting to
waste a good piece of fine silver on a mere test, I decided to design a
slightly more interesting piece that could be worn as a pendant. Accordingly, I
first crafted a textured rectangle of fine silver with a hanging hole.
Before going any
further with my description, I'd like to say a few words about safety
precautions with enamels in general but with leaded enamels in particular. Think about the effect on your lungs of
inhaling powdered glass! Every
step I took during the creation of this color test strip was made while wearing
an N95 3M particulate mask to avoid inhaling the enamel dust. I also mixed,
washed and applied these enamels outdoors on my deck. When I was finished
working, I packed up all my supplies and thoroughly washed down the table on
which I was working (there's nothing quite like wetting enamel to keep the
particles from becoming airborne), washed my hands, stripped off my clothes and
threw them into the washing machine, and took a shower. I didn't want to allow
a single grain of enamel to cling to me anywhere. Always work sensibly with
enamels. Even non-lead-bearing enamels are harmful if inhaled.
Once I had the pendant
fired, burnished and tumbled, I brushed the front of the pendant with enamel
adhesive and then used a sifter to uniformly apply a layer of clear flux
(enamel) over the entire piece. When it was dry, I fired the pendant at 1500
degrees Fahrenheit for exactly two minutes in a pre-heated kiln and then
quickly removed it to cool. Then I did exactly the same thing to the reverse
side of the piece to counter-enamel it. The clear flux acts as a barrier
between the fine silver and the colored enamel to enable the colors to remain
true. Sometimes enamel colors, when applied directly to fine silver, have a
tendency to change. This is especially true with pinks and reds which will
sometimes turn orange when applied to fine silver.
I then applied my
cloisonné wire to the pendant, adhering it by dipping it first into enamel
adhesive. I took care to ensure that I cut the edges of the wire at precise
right angles so all parts of the edges would come in contact with the adjoining
pieces; you don't want to leave any gaps which might allow the enamel to flow
out of its cell or worse, show when you're grinding down your finished piece
and suddenly a gap appears. Once dry, I fired the pendant again. Because the
flux re-melts during firing, the cloisonne wire actually sinks into the flux
and is permanently captured as the piece cools off. Here's how the pendant
looked after the cloisonné wire was fired in place:
You can see that the ends of the cloisonné wire extend over the edges of the
pendant; this is done deliberately to avoid cutting the ends too short. It's
safe to trim this excess wire after the first few coats of enamel have been
applied and fired.
Before proceeding, I drew a rough diagram showing the placement of my wire and
wrote the code numbers of the enamel colors I planned to use into the cells so
I could keep track of which colors I wanted to place where and also have the
ability to remember which colors I used on the test strip for future reference.
Since I had already washed the enamels and placed them into coded jars, I was
ready to roll. I spooned out small amounts of the colors I had selected and
placed them in numerical sequence into a plastic paint tray, adding a few drops
of distilled water to each color to prepare them for wet-packing into the
cells.
Then the fun began as I carefully filled the cells with their assigned colors.
It's not necessary to put down the entire first layer; so I applied just the
first few and fired them in place. Again, 1500 degrees F for two minutes. I
used a tripod because now, with the reverse side of the pendant
counter-enameled, the piece needed to be suspended so that the back wouldn't
melt against the firing surface (a square of mica placed on my kiln furniture
to protect it from the melting enamel). All subsequent firings after the
counter-enameling were done on a tripod.
The applied but unfired enamel almost has the appearance of powdered sugar when
it's dry enough to fire.
I continued to apply the enamel to each cell and fired the pendant. I also
again counter-enameled the back, this time adding a solid color to the entire
reverse side before firing again.
Here, you can see the first full layer of color after firing. It's necessary to
continue applying and firing layers of enamel until they reach or slightly
exceed the height of the cloisonne wire -- any excess can be ground down later,
but ultimately the piece should feel smooth and level to the touch once the
piece is finished.
Repeated firings were done as more and more layers of color were built up on
the piece.
Here's another photo showing how I achieved shading of colors in some of the
cells -- I applied enamel selectively. These areas turned darker when they were
fired.
After the final
layer of enamel had been fired, I finished the test strip by burnishing the
surface under running water with an alundum stone and polishing it with
successively finer grits (120, 200, 400 and 800) of diamond pad grinding sticks.
I carefully removed any remaining glass powder residue with a glass brush and
finally fired the pendant one more time to fire-polish it and return it to a
nice shiny gloss finish.
Once finished, I mounted the pendant on a silver chain and now
wear this piece whenever I'm working with my Japanese enamels as a reminder of
how each color looks once fired.
And instead of having a pile of random wasted color test pieces, I have a lovely cloisonné enamel
pendant I can wear any time!
written by Beverly Miller Gallerani of Mango Tango Designs
Lovely, enamelled ring by Joy Funnell - can you feel the heat?
Beautiful sun pendant with a bit of gold by Jen Kahn. Spiral in the center of this lovely sun is a very old solar symbol.
